Icynene Insulation Removal & Replacement Nationwide

Icynene Insulation Removal & Replacement in Pflugerville: What to Know First

We provide independent Icynene insulation removal and replacement in Pflugerville, TX, with most jobs completed in a single day and your written price delivered before any work starts. As an independent Icynene service provider, we are not affiliated with or authorized by Icynene, but our crews have removed and replaced Icynene open-cell and closed-cell foam systems in hundreds of Central Texas homes, including properties throughout the Stone Hill Town Center corridor and the older subdivisions near downtown Pflugerville.

Call (737) 259-8352

This page is for homeowners who found Icynene in their attic or walls and need it out, whether it is water-damaged, improperly mixed, rodent-contaminated, or simply the wrong product for our climate. Call (737) 259-8352 for a free estimate with a written scope and flat price.

How Icynene Products Fail - and How We Fix Them

• Icynene Classic Max (open-cell) - shrinkage and pull-away from top plates. In Pflugerville’s 100°F+ summer attic temperatures, Classic Max can shrink 5-10% over the first two heating seasons, leaving gaps at the critical junction between wall top plates and the ceiling drywall. We remove the compromised foam with specialized cutting tools, seal the gaps with compatible sealant, and replace with a product better suited to our thermal cycling.
• Icynene MD-R-200 (closed-cell) - off-ratio curing and odor retention. When the A and B components are not mixed precisely, MD-R-200 cures with a persistent chemical odor and reduced R-value. We have stripped out entire attic jobs in Heatherwilde and Windermere where the odor lingered for months. Our fix: complete removal, air scrubbing, and reinstallation with verified-ratio application or alternative material.
• Icynene LD-C-50 (low-density open-cell) - moisture absorption in vented attics. LD-C-50 is vapor-permeable by design, which becomes a problem in Pflugerville homes with bathroom vents dumping into attic space. We have pulled saturated, mold-stained LD-C-50 from attics near Lake Pflugerville where the humidity source was never addressed. We remove, remediate, and specify a proper ventilation or vapor-control strategy before reinstalling.
• Icynene spray foam - rodent nesting and contamination. Once mice or rats tunnel into open-cell foam, the material cannot be sanitized in place. We remove the affected sections, perform full attic decontamination, and install rodent-proofed replacement with exclusion work at entry points.
• Icynene over-application in confined cavities. Overspray of closed-cell foam can bow drywall and compress wall cavities, reducing effectiveness. We have removed over-applied MD-R-200 from utility chases in newer Pflugerville construction where the original crew filled the cavity beyond design thickness. Our fix: controlled removal, cavity assessment, and proper-density replacement.

Our Icynene Insulation Removal & Replacement Process

1. 1
   Call and scheduling. A live person answers 24/7. We book a site visit, and you receive a text when your technician is en route.
2. 2
   On-site diagnosis and blower-door test. We run a blower-door test - a pressurization measurement that shows, in one number, how much air your building envelope is losing. We document the current CFM50 reading, inspect the Icynene product for failure mode, and photograph everything.
3. 3
   Written price and scope. Under Haven Standard Clause 1, you get a flat price, written scope, and written warranty before anyone lifts a tool. No exceptions.
4. 4
   Removal and air sealing. We remove the failed Icynene with foam-cutting equipment and HEPA containment, then seal top plates, can lights, and penetrations before any new insulation goes in. We do not blow insulation over an unsealed attic floor.
5. 5
   Replacement and verification. We install your specified replacement material - from our lineup including Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber - and run a post-job blower-door test. You receive before-and-after CFM50 numbers, a Documented Photo Record, and your warranty paperwork.
6. 6
   365-Day Done Right Promise. If it is not done right, we make it right. The written scope governs what right looks like.

Before

After

What Icynene Insulation Removal & Replacement Costs in Pflugerville

Most Icynene removal and replacement jobs in a Pflugerville home run between $2,800 and $6,500. The price moves based on four factors: square footage of foam to remove, accessibility (steep roof pitch or tight crawl space), whether contamination requires HEPA-level remediation, and the replacement material you select.

A typical 1,500-square-foot attic with open-cell removal and fiberglass batt replacement usually falls near $3,200-$4,400. Closed-cell removal from wall cavities runs higher due to labor density, often $4,500-$6,500. We also handle Reflectix and other brand systems if your project involves mixed materials.

Call (737) 259-8352 for a free estimate. We will read any written quote you have with you, and our second opinion is always free.

Why Pflugerville Homeowners Call Topside Attic Insulation Pflugerville for Icynene Work

We have been in and out of attics throughout Pflugerville’s growth corridors since 2016. The regional heat load patterns here are not a surprise to us. Wes Okafor, who leads this crew, trained in building systems technology at Kennedy-King College on Chicago’s South Side, where instructors drilled air-sealing fundamentals before insulation was ever discussed. That sequence - sealed first, then insulated - is how we still operate.

Every applicable job publishes before-and-after blower-door numbers so you can verify the air-sealing result you paid for. Our materials come from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber - no proprietary lock-in, no pressure to use one brand. Background-checked, uniformed technicians. Live person on the phone. Written price before work starts. The report tells you what the house does. The insulation changes what the house does. Those are two different conversations.

FAQs