Owens Corning Insulation Removal & Replacement Nationwide

Owens Corning Insulation Removal & Replacement in Pflugerville: What to Know First

We provide independent Owens Corning insulation removal and replacement in Pflugerville, TX, with most attic jobs completed in one day and written pricing delivered before any work starts. As an independent Owens Corning service provider, we are not affiliated with or authorized by Owens Corning, but we source their materials alongside Johns Manville, Knauf, and Rockwool, and we know how their products behave in Central Texas heat. Most Pflugerville homeowners with Owens Corning AttiCat blown-in, ProPink Loosefill, or EcoTouch PINK Fiberglas batts call us when insulation has compressed, gotten wet, or been compromised by rodents in the attic. Call (737) 259-8352 for a free estimate with a written price and scope before anyone lifts a tool.

Call (737) 259-8352

How Owens Corning Products Fail - and How We Fix Them

• AttiCat PINK Loosefill compression in Stone Hill Town Center attics. The AttiCat system blows fiberglass at a set density, but in Pflugerville’s 110°F summer attic heat, foot traffic from HVAC contractors and homeowners walking joists grinds the material to half its original depth within five to seven years. We remove the compacted fill with commercial vacuums, seal every top plate and penetration with foam and caulk, then reinstall to the original R-value spec with fresh blown-in or batts.
• ProPink Loosefill moisture saturation from roof leaks. Owens Corning’s ProPink resists mold better than cellulose, but fiberglass still holds water against drywall when roof valleys leak during spring storms. The material cakes into gray mats that weigh three times their dry mass. We bag and remove the saturated insulation, treat the deck with antimicrobial, run a moisture-meter reading on the sheathing, then replace only after the wood reads below 15% moisture content.
• EcoTouch PINK Fiberglas batts pulled apart by squirrels in Blackhawk neighborhoods. The formaldehyde-free binder in post-2015 EcoTouch batts is less appetizing to rodents than older fiberglass, but squirrels still tunnel through for nesting material, especially near gable vents without hardware cloth. We remove the shredded batts, install 1/4-inch galvanized mesh over all vent openings, air-seal the attic floor, then replace with fresh batts or blown-in to eliminate seam gaps the squirrels exploited.
• AttiCat settle-out below R-38 in homes built 2015-2020. Builders in the Heatherwilde and Windermere tracts often specified minimum-code R-30 blown-in that settled to R-24 within three years. Owens Corning labels the settled depth, but homeowners rarely measure. We vacuum the underperforming layer, seal the envelope properly, then install to true R-38 or R-60 depending on the homeowner’s energy audit goals.
• Reflectix radiant barrier degradation when paired with Owens Corning batts. Some Pflugerville installers layered Reflectix bubble-foil directly over PINK batts, trapping humidity between the layers. The foil delaminates and the batts beneath grow mildew. We strip both materials, assess whether radiant barrier is even appropriate for the roof geometry, then reinstall with proper vent baffles and separation.

Our Owens Corning Insulation Removal & Replacement Process

1. 1
   Call and scheduling. A live person answers 24/7. We book a site visit, text the homeowner when the technician is en route, and arrive with a camera, moisture meter, and blower-door rig.
2. 2
   Written assessment and price. We inspect the attic, identify the Owens Corning product line and its condition, and deliver a flat written price with scope and warranty before any work starts. Haven Standard Clause 1: no surprises.
3. 3
   Air sealing first. Every top plate, can light, wire penetration, and duct boot gets sealed with foam or fire-rated caulk. The blower-door test runs before and after sealing so the homeowner sees the CFM50 drop in writing.
4. 4
   Removal and disposal. We vacuum old insulation into sealed bags, HEPA-filtering the attic air. Contaminated material is bagged separately and disposed of per Texas regulations.
5. 5
   Replacement and documentation. New Owens Corning, Johns Manville, Knauf, or Rockwool material goes in to spec. We photograph the completed work, record final blower-door numbers, and hand the homeowner a written report with pre- and post-job CFM50 readings and photos.
6. 6
   365-Day Done Right Promise. If the performance doesn’t match the report, we return and make it right. The warranty and scope were already in writing before we started.

Before

After

What Owens Corning Insulation Removal & Replacement Costs in Pflugerville

What moves the price: attic square footage, accessibility (scuttle vs. pull-down stairs), contamination level, whether the home needs new vent baffles or soffit extension, and whether we are matching existing Owens Corning specs or upgrading to a higher R-value. We also provide a Free Second Opinion on any written estimate from another contractor. Call (737) 259-8352 for a written price before any work starts.

Why Pflugerville Homeowners Call Topside Attic Insulation Pflugerville for Owens Corning Work

We’ve been in attics throughout Pflugerville since 2016, and the regional heat load patterns in the Stone Hill Town Center corridor are not a surprise to us. Wes Okafor, our owner, trained in building systems technology at Kennedy-King College on Chicago’s South Side, where the curriculum drilled air-sealing fundamentals before insulation installation. That shows up in our work: we seal first, insulate second, and publish blower-door numbers so the homeowner can verify the result. The 365-Day Done Right Promise applies to every job, backed by a written scope delivered before anyone starts. If Owens Corning material is back-ordered, we have working relationships with Johns Manville, Knauf, Rockwool, and Reflectix suppliers, so the job doesn’t stall. Calls are answered by a live person 24/7, and every visit produces a Documented Photo Record, included, not available on request.

FAQs