Reflectix Insulation Service Nationwide

Why Pflugerville Homeowners Choose Reflectix Insulation

We provide Reflectix in Pflugerville as an independent insulation service, from Stone Hill Town Center to Blackhawk and Springbrook. Our crews handle Reflectix radiant barrier installation, repair, and reconfiguration in attics where the original install was done wrong, and we publish before-and-after blower-door numbers on every job so you can verify the air-sealing result in actual CFM50. Call (737) 259-8352 for a written price before any work starts.

Call (737) 259-8352

Reflectix products - foil-faced bubble-core rolls and perforated radiant barrier sheets - are common in Pflugerville attics because they’re lightweight, readily available, and marketed as a DIY solution. The problem is that performance depends entirely on proper orientation, air gaps, and sealed seams. In the 2000s-era production homes that dominate this market, we’ve found more failed Reflectix installs than successful ones. The material itself is sound. The execution usually isn’t.

We are not affiliated with, authorized by, or sponsored by Reflectix Inc. We buy their products through standard distribution channels and install them as an independent service provider. No manufacturer warranty extends to our labor.

Why Trust Topside Attic Insulation Pflugerville for Your Reflectix Insulation?

Wes Okafor, who leads our crew, trained in building systems technology at Kennedy-King College on Chicago’s South Side, where the curriculum drilled air-sealing fundamentals before insulation was even discussed. That sequence - seal first, then insulate - is how we approach every Attic Insulation services job involving Reflectix in Pflugerville. We’ve been in and out of attics along the Stone Hill Town Center corridor often enough that the regional heat load patterns aren’t a surprise. When a homeowner calls about a hot second floor, we already know the likely roof pitch, the original R-30 blown fiberglass spec, and whether the builder left room for proper baffles.

We carry genuine Reflectix rolls in 16-inch and 24-inch widths, both perforated and non-perforated, because generic foil-bubble substitutes vary in emissivity and bubble height. Those numbers matter. A 0.03 emissivity surface reflects 97% of radiant heat; a 0.10 generic foil might only manage 90%. In a Pflugerville attic hitting 150°F, that gap translates to real temperature difference downstairs.

Our documentation is what sets us apart. You get a written scope, a written price, and a written warranty before anyone lifts a tool. On applicable jobs, we run a blower-door test - a pressurization reading that shows, in one number, how much air your building envelope is losing - and hand you the pre- and post-job report with actual CFM50 readings. The report tells you what the house does. The insulation changes what the house does. Those are two different conversations.

Common Reflectix Insulation Problems We Fix in Pflugerville

• Shiny-side-up installation with untaped seams. This is the single most common Reflectix failure we see in Pflugerville. A homeowner buys a Reflectix Double Reflective Insulation Roll, staples it shiny-side-up to the underside of the rafters, and leaves the butt seams unsealed. The shiny side should face an air space; facing it up toward the hot roof deck means it absorbs radiant heat rather than reflecting it back. Untaped seams let that heat bypass the barrier entirely. We diagnose this in about thirty seconds with a visual inspection and an infrared thermometer.
• Compression or crushing of the bubble core. The Reflectix Double Reflective Foil Insulation achieves its rated performance partly through the trapped air in its bubble core. When a later trade - an HVAC tech, a roofer, a pest control operator - walks on it or piles material against it, those bubbles collapse. The product’s effective R-value drops toward its foil-only rating, which is minimal. We find this especially in Pflugerville attics where blown fiberglass was added after the Reflectix went in, burying the barrier under weight and eliminating its required air gap.
• Moisture trapping in non-perforated installs. Reflectix makes both perforated and non-perforated rolls. A non-perforated product installed on a roof deck in Pflugerville’s hot-humid Climate Zone 2 can trap water vapor that migrates up from the conditioned space. Over time, this stains the foil, degrades the adhesive on any tape, and can contribute to mold on the roof deck. We specify perforated Reflectix Radiant Barrier Perforated Roll for roof deck applications so the assembly can dry to the exterior.
• Foil surface abrasion from attic traffic and pests. The low-emissivity surface that makes Reflectix work is a thin metalized coating. Scratch it, and the underlying plastic substrate absorbs heat instead of reflecting it. Squirrels, raccoons, and even careless HVAC technicians can damage enough surface area to measurably reduce performance. We document this with photos and mark damaged sections on your written report.
• DIY installs that block soffit ventilation. A Reflectix roll run continuously from eave to ridge without baffles chokes the airflow path that Pflugerville’s attic ventilation depends on. The ridge vent can’t pull if the soffit intake is blocked. We see this in production homes where the original builder skipped baffles and a later homeowner added Reflectix without understanding the interaction. Our fix: install proper attic baffles and ventilation prep before any radiant barrier goes back up.

Before

After

Reflectix Parts & Our Repair-vs-Replace Approach

We buy genuine Reflectix rolls rather than substituting generic foil-bubble products. The emissivity spec is printed on the roll, and we verify it. For most Pflugerville attics, we stock 24-inch perforated radiant barrier for roof deck applications and 16-inch non-perforated bubble core for crawl space or wall cavity work, similar to how we handle Reflectix Insulation in Wells Branch, TX.

Where your existing Reflectix is intact but poorly installed, we re-tension, re-seam, and re-staple it. Replacement only makes sense when the reflective surface is abraded, moisture-stained, or the bubbles are crushed flat. We’ll show you the damage on our documented photo record and explain the calculation. No upsell. Call (737) 259-8352 for a written price either way.

Our Reflectix Service Process - Step by Step

1. 1
   Diagnosis. We inspect orientation, seam sealing, bubble core integrity, and foil surface condition. We check whether your soffits are blocked and whether the original builder installed baffles. On applicable jobs, we run a blower-door test to quantify air leakage before any work begins.
2. 2
   Repair or install. We remove failed material, reconfigure correct Reflectix products with proper air gaps, and tape all seams with manufacturer-compatible foil tape. For roof deck applications, we use perforated Reflectix with shiny side facing down toward the attic space.
3. 3
   Test and verify. We confirm baffle clearance, ridge vent pull, and - on jobs with air-sealing scope - re-run the blower-door test to document improvement. You get the numbers in writing.
4. 4
   Warranty and record. Your documented photo record, written scope, and 365-Day Done Right Promise are delivered before we leave. Haven Standard: Have it in writing.

Reflectix Products We Service & Install in Pflugerville

• Reflectix Double Reflective Insulation Roll - 16 in and 24 in widths, bubble core, for attic floor or crawl space applications
• Reflectix Double Reflective Foil Insulation - R-21 rated roll product for wall cavities and framed assemblies
• Reflectix Reflective Foam Core Insulation - higher R-value product for applications needing more thermal resistance
• Reflectix Radiant Barrier Perforated Roll - roof deck and rafter applications where vapor permeability is required

We stock the two most common widths in Pflugerville for same-day turnaround on most jobs.

We Also Service These Brands

Our crews work with Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber products. We’re not locked to any single manufacturer. If your attic needs a hybrid solution - Reflectix service in Round Rock areas also uses Reflectix radiant barrier plus blown-in fiberglass, or spray foam at the roofline with a reflective face - we specify what performs, not what we’re pushed to sell.

FAQs - Reflectix Insulation Service in Pflugerville

Is Topside Attic Insulation Pflugerville authorized by Reflectix?

No. We are an independent Reflectix service provider. Reflectix does not authorize, sponsor, or warranty our work. We purchase their products through standard distribution and install them according to building science principles and local code.

Do you use genuine Reflectix/OEM parts?

Yes. We buy genuine Reflectix rolls in the correct width and perforation for each application. We do not substitute generic foil-bubble products that vary in emissivity and bubble height.

How long does Reflectix service take?

Most attic reconfigurations in Pflugerville take one day. A full roof-deck install on a typical 2,000-square-foot home takes one to two days depending on pitch and accessibility. We give you a written schedule with the price. Call (737) 259-8352 for availability.

What Reflectix models/series do you cover?

We service and install all current Reflectix product lines: Double Reflective Insulation Roll, Double Reflective Foil Insulation, Reflective Foam Core Insulation, and Radiant Barrier Perforated Roll. If you have a discontinued product, we’ll assess whether it’s salvageable or needs replacement.

Will service void my Reflectix warranty?

Reflectix’s product warranty covers manufacturing defects, not installation. Our labor is separate and carries its own 365-Day Done Right Promise. As an independent provider, we do not extend or alter any manufacturer warranty.

How much does Reflectix insulation cost in Pflugerville?

Most attic radiant barrier reconfigurations run $1,800-$3,400 depending on square footage, existing material removal, and whether air sealing is needed. Roof-deck installs on typical Pflugerville tract homes range $2,400-$4,200. We provide a written price before any work starts. Call (737) 259-8352 for an exact quote on your home.

Does Reflectix radiant barrier make sense in a Pflugerville attic, or is more blown-in insulation the better buy?

In Pflugerville’s Climate Zone 2, radiant heat from a 150°F roof deck is the dominant cooling load. Reflectix addresses that directly. Blown-in insulation slows conductive heat flow but does nothing for radiant. The best-performing attics we see in Pflugerville combine both: a radiant barrier at the roof deck, proper ventilation, and adequate insulation at the attic floor. If your home is one of the 2000s-era production builds with settled R-30 fiberglass, you likely need both upgrades.

Should Reflectix be installed shiny-side-up or shiny-side-down?

It depends on location. For roof deck or rafter applications, shiny side faces down toward the attic air space. For crawl space or floor applications, shiny side faces up toward the subfloor. The key is that the reflective surface must face an air gap; contact with another material eliminates the radiant barrier effect. We see this wrong about half the time in Pflugerville DIY installs.

Will a Reflectix radiant barrier trap moisture on my roof deck in Central Texas humidity?

Only if you use the non-perforated product. We specify Reflectix Radiant Barrier Perforated Roll for all Pflugerville roof deck work so water vapor can migrate through and escape via ridge ventilation. We also verify that your soffit and ridge venting is functional before install.

My existing Reflectix was installed by a previous owner and looks fine - can you just top up the attic insulation around it?

We won’t blow insulation over an unsealed attic floor or a misconfigured radiant barrier. First we inspect orientation, seam sealing, and bubble core condition. If the Reflectix is correctly installed and intact, we can work with it. If it’s shiny-side-up with untaped seams or crushed core, we reconfigure it first. The insulation goes in last, not first.

Can Reflectix be used in a Pflugerville crawl space instead of a vapor barrier?

Reflectix is not a vapor barrier. Its perm rating is too high to block ground moisture migration. For crawl space encapsulation in Pflugerville’s humid climate, we use dedicated vapor barrier products - 6-mil polyethylene minimum, often 12-mil reinforced - and seal all seams and piers. Reflectix can supplement as an insulation layer on crawl space walls, but it cannot replace a proper vapor barrier.

Book Your Reflectix Service in Pflugerville, TX

Call (737) 259-8352 to speak with a live person - no voicemail loops, no callback windows measured in business days. We’ll schedule a site visit, provide a written price before any work starts, and deliver a documented photo record with your completed job. Every applicable project includes before-and-after blower-door numbers so you can verify what changed.

Written by Wes Okafor, Owner at Topside Attic Insulation Pflugerville, serving Pflugerville since 2016.